302-02804TAMPING RAMMERINSTRUCTION MANUALMTXSERIES
Places where decals are attached 02#STOP02#02#113574 2 1Engine Oil Use SAE 10W/30,SE or higher grade motor oil RAMMING CYLINDER OIL Us
ᵫᵧᵩᵟᵱᵟᴾᵱᵟᵬᵥᵷᵭᴾᵡᵭᵌᵊᵪᵲᵢᵏᵋᵒᵋᵑᵊᵱᵿᶐᶓᶅᵿᶉᶓᵋᶁᶆᶍᵊᵡᶆᶇᶗᶍᶂᵿᵋᶉᶓᵊᵲᶍᶉᶗᶍᵊᵨᵿᶎᵿᶌMade in Japan17627627+55/#:+.'+560)216'0<#/#55+/#216'0%+#/#:9&
350/MTX-60,70365/MTX-80,90713/MTX-60788/MTX-70,80,90 985/MTX-601000/MTX-70,80,90340Dimentions 8265/MTX-60285/MTX-70,80,90
MUFFLER ASSYHANDLE ASSYHOOKFUEL TANK CAP ASSYFUEL TANK ASSYENGINE ASSYBELLOWSFOOT ASSYCOMBINATION LEVER ASSYComponents9ROLLER ASSYRECOIL STARTEROIL GA
Inspection itemsFlaws, deformity, stainsStains, flaws, deformationLoose or missing partsFlaws, deformity, cracks, breaksFlaws, deformity, cracks, brea
StartingAdd regular gasoline (Unleaded) to the fuel tank and check the engine oil. Add oil before it gets too low. Too little engine oil may cause the
OperationAfter the engine has started, open the choke lever gradually until it is wide open. Pay attention to the sound of the engine to guide you in
In the cold season, the oil in the machine will be thicker, and the resistance of the components will be much larger, which may cause irregular motion
Wash off any dirt or mud on each part of the machine using fresh water.After the engine and main body have cooled down, store the rammer on a level lo
Daily maintenanceCarefully wipe off any mud, dirt or oil from each component.If oil leaks, retighten the joints and check again.Maintenance after ever
5) modelMTX-60 MTX-70 MTX-80 MTX-906) Equipmentitem number51087 5108951228 512295123351265 51267 51275 512777) power sorce Honda GX100U1.7kWHonda GX10
Secondary element (clean every 100 to 150 hours)When the secondary element (under the primary element) becomes dirty, wash it with neutral detergent s
Engine1.Won't startTroubleshootingFuel is present but the spark plug is not sparking.Fuel and spark are both present.Fuel is not being supplied t
Note- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - -
㪪㫇㪼㪺㫀㪽㫀㪺㪸㫋㫀㫆㫅㩷㪽㫆㫉㩷㪤㪫㪯㪄㫊㪼㫉㫀㪼㫊㪇㪎㩾㪄㪈㪉㪄㪉㪌Rammer SpecificationsModel MTX-60 MTX-70 MTX-80 MTX-90Overall height mm 985 1,000 1,000 1,000Overall width mm 350
MTX TAMPING RAMMER INSTRUCTION MANUALTable of contentsPrefaceApplicationWarning about incorrect applications and techniquesStructurePower transmission
PrefaceThis instruction manual describes the proper methods for using the tamping rammer, as well as simple checks and maintenance. Be sure to read th
The triangle shaped marks used in this manual and on the decals stuck on the main body indicate common hazards. Be sure to read and observe the cautio
Precautions when adding fuelDANGER䋣When adding fuel.Adding fuel until it comes too close to the top of the inlet may cause the fuel to overflow. That
Precautions before starting work(Continued)DANGER䋣If the machine falls over while working, the machine will move forward due to the kicking motion of
Transportation and storage precautionsDANGER䋣When transportingBefore transporting the machine, stop the engine.DO NOT try to move it before the engine
Comments to this Manuals